OPEN INSTRUMENT DESK
SLA: 100% Client-Side Privacy
← Calculators
Sponsored Advertisement
Leaderboard Display Ad (728x90 Desktop / 300x250 Mobile Slot)
Loose Aggregate Density Model

Gravel Ton Calculator for Driveway

Convert any driveway footprint into cubic yards (L × W × D / 324), then into loose tons using real per-material densities — with delivered cost and dump truck load sizing.

Driveway Dimensions & Material

Loose density: 2,650 lb / cu yd
Regional range: $35–$65 / ton delivered
cu yd per truck
Computed Output 0ms Latency
Total Gravel Required
11.77 Tons
≈ 23,540 lb loose aggregate
Total Volume (L × W × D ÷ 324): 8.89 cu yd
Estimated Delivered Cost: $529.50
Dump Truck Loads Required: 1 Load
Per-Load Weight: 11.77 tons
Truck Plan

A 14 cu yd truck covers your 8.89 cu yd job in 1 load (≈ 11.77 tons of ABC / Crusher Run).

Sponsored Contractor Ad
Sidebar Display Ad (300x250 Medium Rectangle Slot)
Internal Knowledge Graph

Related Construction & DIY Calculators

Explore All Construction & DIY Tools →
Affiliate Recommendation

Equipment for Hauling, Spreading & Compacting Gravel

FTC Disclosure: We may earn a commission on qualifying purchases.
Equipment Dealer

Bobcat S70 Skid Steer

Move and spread 10+ yard gravel deliveries from the stockpile to the drive in a single pass; pairs with a 1.4 cu yd bucket.

Equipment Dealer

Bobcat Vibratory Plate Compactor

Locks down crusher-run base layers in compacted lifts so the driveway surface never ruts or washes.

Amazon Pro / Supply House

RIDGID SeeSnake Camera Inspection System

Verify drain and utility paths under the new gravel bed before you grade — avoids re-opening a freshly laid base.

How to Calculate Gravel Tons: The Formula

Driveway material is sold by the ton, but jobs are measured in feet and inches. The bridge between the two is loose density — the weight of one cubic yard of un-compacted aggregate. First compute volume with the 324 rule, then multiply by the material's density and divide by 2,000 lb per ton.

Standard Imperial Gravel Formula
Cubic Yards = L (ft) × W (ft) × D (in) ÷ 324
Tons = Cubic Yards × Density (lb/yd³) ÷ 2,000

Where "324" Comes From

One cubic yard equals 27 cubic feet. Depth is measured in inches, and 12 inches make a foot, so every additional depth inch contributes 1/12 of a foot of volume. Multiplying the two constants — 27 cu ft per cubic yard × 12 in per foot — gives 324. That single divisor collapses length, width, and depth into cubic yards with no intermediate conversion.

Step Example (40 × 12 ft @ 6 in)
1. Volume 40 × 12 × 6 ÷ 324 = 8.89 cu yd
2. Apply density (ABC, 2,650 lb/yd³) 8.89 × 2,650 = 23,558 lb
3. Convert to tons 23,558 ÷ 2,000 = 11.78 tons

Loose Aggregate Density Table

Densities below are the loose (un-compacted) values gravel yards use when pricing truckloads. Compacted stone can run 10–15% heavier, which is why the calculator reports tons from the loose figure — the same basis your supplier will quote.

Material Loose Density (lb/yd³) Typical Use
#57 Crushed Stone 2,700 Concrete sub-base, drainage fill
ABC / Crusher Run 2,650 Driveway base, roadbeds, building pads
3/8" Pea Gravel 2,600 Decorative walkways, French drain fill
3/4" Dense Grade 2,500 Top-wear layer, sloped driveways
Rip Rap / Erosion Control 2,400 Riverbanks, storm channels, slope armor
Septic Stone 2,700 Drain field beds, septic tile systems

Sizing the Dump Truck

Most yard trucks deliver 10–20 cubic yards per load. A mid-size unit takes about 14 cu yd; a larger unit about 16 cu yd; full-size loads are frequently rated by weight near 20 tons. The estimator above converts a ton-rated truck into yardage using your selected material's density, so a 20-ton load of light Rip Rap (≈ 16.7 cu yd) and a 20-ton load of heavy #57 (≈ 14.8 cu yd) are sized correctly.

Frequently Asked Questions (FAQ)

How many tons of gravel do I need for a 12×40 ft driveway with 6 inches of depth?

Volume is 12 × 40 × 6 ÷ 324 = 8.89 cubic yards. At ABC / Crusher Run (2,650 lb/yd³) that is 8.89 × 2,650 ÷ 2,000 = 11.78 tons — one standard 14-yard truck.

Why is the volume formula Length × Width × Depth divided by 324?

A cubic yard contains 27 cubic feet (3 × 3 × 3). Converting depth from inches to feet divides by 12. Multiplying those constants (27 × 12) gives 324, so L(ft) × W(ft) × D(in) ÷ 324 yields cubic yards directly.

How many cubic yards does a dump truck hold?

Common driveway deliveries run 10–20 cubic yards. A mid-size truck carries about 14 cu yd, a larger unit about 16 cu yd, and full-size loads are often rated by weight near 20 tons. At 2,650 lb/yd³, a 16-yard truck holds roughly 31 tons of loose material.

Does the material change the tonnage I order?

Yes. Cubic yards stay the same for a fixed area and depth, but loose density varies: #57 and septic stone run about 2,700 lb/yd³ while rip rap runs about 2,400. The same 8.89 yards weighs 11.9 tons as ABC but only 10.7 tons as rip rap.

Should I add extra gravel for settling and grading?

Loose aggregate settles and is lost to compaction, so most contractors order 5%–10% more than the calculated volume for driveways. Adding that buffer before converting to tons avoids a costly second delivery.